Filters
Question type
Study Flashcards

Which Cisco IOS command is used to enable a switch interface to become a routed port?


A) sdm prefer routing
B) ip route enable
C) no switchport
D) ip routing

Correct Answer

verifed

verified

C

If configuring a layer 3 EtherChannel using two physical interfaces, how many different times must the no switchport command be configured?


A) 1
B) 2
C) 3
D) Never

Correct Answer

verifed

verified

Which Cisco IOS command is used to make memory space available for IPv4 routes on a 2960 series of switches?


A) sdm prefer lanbase-routing
B) sdm prefer ipv4-routing
C) ip routing
D) routing enable

Correct Answer

verifed

verified

Which Cisco IOS command is used to enable a router subinterface with 802.1Q and associate it with a specific VLAN?


A) vlan vlan-id
B) encapsulation dot1q vlan-id
C) encapsulation vlan vlan-id
D) dot1q vlan-id

Correct Answer

verifed

verified

Which Cisco IOS command would be used to configure a router subinterface to handle any native VLAN traffic?


A) dot1q native
B) vlan vlan-id native
C) native vlan
D) encapsulation dot1q vlan-id native

Correct Answer

verifed

verified

Which Cisco IOS command can be used on a switch to verify that an interface has been configured as a routed port by indicating that it is "routed"?


A) show interfaces
B) show interface interface switchport
C) show ip route
D) show interface status

Correct Answer

verifed

verified

Which Cisco IOS command would be used to display the state and type of EtherChannel configured on a device?


A) show running-config
B) show ether channel
C) show etherchannel summary
D) show interface bundle

Correct Answer

verifed

verified

C

Which Cisco IOS command(s) would be used to configure an interface in a static layer 3 EtherChannel?


A) channel-group number mode on
B) no switchport
C) channel-group number mode on layer-3
D) ip routing enable

Correct Answer

verifed

verified

A, B

Which Cisco IOS command can be used on a switch to verify that a trunk has been configured on the interface connected to a router configured with ROAS and the VLANs that are allowed, not blocked, and not pruned?


A) show interfaces roas
B) show trunk
C) show vlans
D) show interfaces trunk

Correct Answer

verifed

verified

Which Cisco IOS command is used to create a new SVI on a switch?


A) interface vlan vlan-id
B) vlan vlan-id
C) switchport access vlan vlan-id
D) interface svi vlan-id

Correct Answer

verifed

verified

Which Cisco IOS command is used to enable IPv4 routing on a 2960 series switch?


A) sdm prefer lanbase-routing
B) ip routing
C) sdm prefer ipv4-routing
D) routing enable

Correct Answer

verifed

verified

Which Cisco IOS command can be used to display the ROAS configuration on a router?


A) show roas
B) show vlan
C) show vlans
D) show interfaces vlan

Correct Answer

verifed

verified

For a VLAN SVI to be in the up/up state, which option is not required?


A) The VLAN must be defined locally.
B) The VLAN must have an entry in the MAC address table.
C) An access link or trunk must be configured and optional in the VLAN (not blocked or pruned) .
D) The VLAN SVI must be enabled.

Correct Answer

verifed

verified

When configuring a switch to connect to a router that is being configured with a ROAS configuration, which Cisco IOS command must be entered on the interface to ensure that the link forms a trunk?


A) switchport mode trunk
B) switchport mode dynamic desirable
C) switchport mode access
D) switchport mode trunk router

Correct Answer

verifed

verified

Which of the LAN routing options shown is not typically used?


A) Using a layer 3 switch using routed ports
B) Using a layer 3 switch using SVIs
C) Using a router configured with a VLAN trunk
D) Using a router with a physical interface associated with each individual VLAN

Correct Answer

verifed

verified

Showing 1 - 15 of 15

Related Exams

Exam 1

Introduction to TCP/IP Networking

17 Questions

Exam 2

Fundamentals of Ethernet Lans

22 Questions

Exam 3

Fundamentals of Wans and IP Routing

8 Questions

Exam 4

Using the Command-Line Interface

15 Questions

Exam 5

Analyzing Ethernet Lan Switching

15 Questions

Exam 6

Configuring Basic Switch Management

15 Questions

Exam 7

Configuring and Verifying Switch Interfaces

7 Questions

Exam 8

Implementing Ethernet Virtual Lans

16 Questions

Exam 9

Spanning Tree Protocol Concepts

17 Questions

Exam 10

RSTP and Etherchannel Configuration

20 Questions

Exam 11

Perspectives on IPV4 Subnetting

26 Questions

Exam 12

Analyzing Classful IPV4 Networks

15 Questions

Exam 13

Analyzing Subnet Masks

19 Questions

Exam 14

Analyzing Existing Subnets

29 Questions

Exam 15

Operating Cisco Routers

15 Questions

Exam 16

Configuring IPV4 Addresses and Static Routes

11 Questions

Exam 18

Troubleshooting IPV4 Routing

7 Questions

Exam 19

Understanding OSPF Concepts

17 Questions

Exam 20

Implementing OSPF

19 Questions

Exam 21

OSPF Network Types and Neighbors

15 Questions

Exam 22

Fundamentals of IP Version 6

14 Questions

Exam 23

Ipv6 Addressing and Subnetting

14 Questions

Exam 24

Implementing IPV6 Addressing on Routers

15 Questions

Exam 25

Implementing IPV6 Routing

14 Questions

Exam 26

Fundamentals of Wireless Networks

12 Questions

Exam 27

Analyzing Cisco Wireless Architectures

12 Questions

Exam 28

Securing Wireless Networks

12 Questions

Exam 29

Building a Wireless Lan

12 Questions

Show Answer