Filters
Question type
Study Flashcards

Two technicians are discussing scrub radius. Technician A says that scrub radius cannot be measured. Technician B says that scrub radius cannot be adjusted. Which technician is correct?


A) Technician A only
B) Technician B only
C) Both technicians A and B
D) Neither technician A nor B

Correct Answer

verifed

verified

Which statement(s) is/are TRUE about included angle?


A) It is only measured on the front suspension
B) It is calculated by adding camber and SAI
C) Both A and B
D) Neither A nor B

Correct Answer

verifed

verified

What is the maximum amount generally allowed for camber side-to-side difference?


A) 0 degrees
B) 1 degree
C) 1/2 degree
D) None of these are correct

Correct Answer

verifed

verified

A vehicle will pull to the side with the least positive caster.

Correct Answer

verifed

verified

What alignment angle is shown in this drawing? What alignment angle is shown in this drawing? A) Total toe B) Thrust angle C) Center line D) Rear camber


A) Total toe
B) Thrust angle
C) Center line
D) Rear camber

Correct Answer

verifed

verified

What term describes the inward tilt of the steering axis?


A) SAI
B) King pin inclination
C) Both A and B
D) Neither A nor B

Correct Answer

verifed

verified

Which of these statements is TRUE regarding scrub radius?


A) It cannot be adjusted
B) It can be measured
C) Both A and B
D) Neither A nor B

Correct Answer

verifed

verified

Excessive toe-in will cause tire wear ________.


A) In the middle of the tire
B) On the outside shoulder of the tire
C) On both tire edges
D) On the inside shoulder of the tire

Correct Answer

verifed

verified

When performing an alignment, which angle is the most important for tire wear?


A) SAI
B) Toe
C) Caster
D) Camber

Correct Answer

verifed

verified

A vehicle will pull to the side with the most (positive) toe.

Correct Answer

verifed

verified

Excessive negative camber will cause which of the following?


A) Excessive wheel bearing loading
B) Improper handling
C) Inner tire wear
D) All of these are correct

Correct Answer

verifed

verified

Many manufacturers specify some degree of ________ toe.


A) Negative
B) Zero
C) Positive
D) None of these

Correct Answer

verifed

verified

Excessive positive camber will cause tire wear ________.


A) In the middle of the tire
B) On the inside shoulder of the tire
C) On the outside shoulder of the tire
D) On both tire edges

Correct Answer

verifed

verified

What alignment angle is shown here? What alignment angle is shown here? A) Toe in B) Caster C) Toe out D) Camber


A) Toe in
B) Caster
C) Toe out
D) Camber

Correct Answer

verifed

verified

Positive camber means ________.


A) The top of the tire is tilted outward
B) The top of the tire is tilted inward
C) Either A or B
D) Both A and B

Correct Answer

verifed

verified

Showing 21 - 35 of 35

Related Exams

Exam 1

Automotive Background and Overview

32 Questions

Exam 2

Careers in the Automotive Service Industry

30 Questions

Exam 3

Starting a Career in the Automotive Industry

30 Questions

Exam 4

Working As a Professional Service Technician

31 Questions

Exam 5

Technician Certification

28 Questions

Exam 6

Shop Safety

31 Questions

Exam 7

Environmental and Hazardous Materials

24 Questions

Exam 8

Fasteners and Thread Repair

34 Questions

Exam 9

Hand Tools

25 Questions

Exam 10

Power Tools and Shop Equipment

30 Questions

Exam 11

Vehicle Lifting and Hoisting

24 Questions

Exam 12

Measuring Systems and Tools

30 Questions

Exam 13

Scientific Principles and Materials

31 Questions

Exam 14

Math, Charts, and Calculations

30 Questions

Exam 15

Service Information

28 Questions

Exam 16

Vehicle Identification and Emission Ratings

28 Questions

Exam 17

Preventative Maintenance and Service Procedures

30 Questions

Exam 18

Gasoline Engine Operation, Parts, and Specifications

10 Questions

Exam 19

Diesel Engine Operation and Diagnosis

30 Questions

Exam 20

Coolant

22 Questions

Exam 21

Cooling System Operation and Diagnosis

24 Questions

Exam 22

Engine Oil

24 Questions

Exam 23

Lubrication System Operation and Diagnosis

21 Questions

Exam 24

Intake and Exhaust Systems

20 Questions

Exam 25

Turbocharging and Supercharging

22 Questions

Exam 26

Engine Condition Diagnosis

15 Questions

Exam 27

In-Vehicle Engine Service

2 Questions

Exam 28

Engine Removal and Disassembly

22 Questions

Exam 29

Engine Cleaning and Crack Detection

22 Questions

Exam 30

Cylinder Head and Valve Guide Service

22 Questions

Exam 31

Valve and Seat Service

22 Questions

Exam 32

Camshafts and Valve Trains

27 Questions

Exam 33

Pistons, Rings, and Connecting Rods

22 Questions

Exam 34

Engine Blocks

24 Questions

Exam 35

Crankshafts, Balance Shafts, and Bearings

25 Questions

Exam 36

Gaskets and Sealants

20 Questions

Exam 37

Engine Assembly and Dynamometer Testing

33 Questions

Exam 38

Engine Installation and Break-In

20 Questions

Exam 39

Electrical Fundamentals

24 Questions

Exam 40

Electrical Circuits and Ohms Law

20 Questions

Exam 41

Series, Parallel, and Series-Parallel Circuits

29 Questions

Exam 42

Circuit Testers and Digital Meters

2 Questions

Exam 44

Automotive Wiring and Wire Repair

26 Questions

Exam 45

Wiring Schematics and Circuit Testing

19 Questions

Exam 46

Capacitance and Capacitors

10 Questions

Exam 47

Magnetism and Electromagnetism

10 Questions

Exam 48

Electronic Fundamentals

4 Questions

Exam 49

Can and Network Communications

4 Questions

Exam 50

Batteries

13 Questions

Exam 51

Battery Testing and Service

13 Questions

Exam 52

Cranking System

12 Questions

Exam 53

Cranking System Diagnosis and Service

14 Questions

Exam 54

Charging System

16 Questions

Exam 55

Charging System Diagnosis and Service

9 Questions

Exam 56

Lighting and Signaling Circuits

15 Questions

Exam 57

Driver Information and Navigation Systems

20 Questions

Exam 58

Horn, Wiper, and Blower Motor Circuits

12 Questions

Exam 59

Accessory Circuits

14 Questions

Exam 60

Airbags and Pretensioner Circuits

14 Questions

Exam 61

Audio System Operation and Diagnosis

17 Questions

Exam 62

Heating and Air-Conditioning Components and Operation

29 Questions

Exam 63

Automatic Air-Conditioning System Operation

22 Questions

Exam 64

Heating and Air-Conditioning System Diagnosis

25 Questions

Exam 65

Heating and Air-Conditioning System Service

25 Questions

Exam 66

Gasoline

15 Questions

Exam 67

Alternative Fuels

17 Questions

Exam 68

Diesel and Biodiesel Fuels

27 Questions

Exam 69

Ignition System Components and Operation

25 Questions

Exam 70

Ignition System Diagnosis and Service

18 Questions

Exam 71

Computer Fundamentals

12 Questions

Exam 72

Temperature Sensors

6 Questions

Exam 73

Throttle Position Tp Sensors

10 Questions

Exam 74

Mapbaro Sensors

6 Questions

Exam 75

Mass Air Flow Sensors

12 Questions

Exam 76

Oxygen Sensors

6 Questions

Exam 77

Fuel Pumps, Lines, and Filters

6 Questions

Exam 78

Fuel-Injection Components and Operation

5 Questions

Exam 79

Gasoline Direct-Injection Systems

2 Questions

Exam 80

Electronic Throttle Control System

3 Questions

Exam 81

Fuel-Injection System Diagnosis and Service

8 Questions

Exam 82

Vehicle Emission Standards and Testing

6 Questions

Exam 83

Evaporative Emission Control Systems

18 Questions

Exam 84

Exhaust Gas Recirculation Systems

15 Questions

Exam 85

Positive Crankcase Ventilation and Secondary Air-Injection Systems

12 Questions

Exam 86

Catalytic Converters

17 Questions

Exam 87

Onboard Diagnosis

1 Questions

Exam 88

Scan Tools and Engine Performance Diagnosis

5 Questions

Exam 89

Introduction to Hybrid Vehicles

22 Questions

Exam 90

Hybrid Safety and Service Procedures

21 Questions

Exam 91

Fuel Cells and Advanced Technologies

22 Questions

Exam 92

Braking System Components and Performance Standards

26 Questions

Exam 93

Braking System Principles

27 Questions

Exam 94

Brake Hydraulic Systems

31 Questions

Exam 95

Hydraulic Valves and Switches

30 Questions

Exam 96

Brake Fluid and Lines

28 Questions

Exam 97

Brake Bleeding Methods and Procedures

28 Questions

Exam 98

Wheel Bearings and Service

26 Questions

Exam 99

Drum Brakes

37 Questions

Exam 100

Drum Brake Diagnosis and Service

30 Questions

Exam 101

Disc Brakes

32 Questions

Exam 102

Disc Brakes Diagnosis and Service

28 Questions

Exam 103

Parking Brake Operation, Diagnosis, and Service

25 Questions

Exam 104

Machining Brake Drums and Rotors

25 Questions

Exam 105

Power Brake Unit Operation, Diagnosis, and Service

25 Questions

Exam 106

Abs Components and Operation

24 Questions

Exam 107

Abs Diagnosis and Service

21 Questions

Exam 108

Electronic Stability Control Systems

20 Questions

Exam 109

Tires and Wheels

32 Questions

Exam 110

Tire Pressure Monitoring Systems

21 Questions

Exam 111

Tire and Wheel Service

30 Questions

Exam 112

Suspension System Principles and Components

31 Questions

Exam 113

Front Suspensions and Service

32 Questions

Exam 114

Rear Suspensions and Service

30 Questions

Exam 115

Electronic Suspension Systems

30 Questions

Exam 116

Steering Columns and Gears

29 Questions

Exam 117

Steering Linkage and Service

28 Questions

Exam 118

Power-Assisted Steering Operation and Service

30 Questions

Exam 120

Alignment Diagnosis and Service

30 Questions

Exam 121

Clutches

30 Questions

Exam 122

Manual Transmissions/Transaxles

22 Questions

Exam 123

Drive Axle Shafts and Cv Joints

30 Questions

Exam 124

Drive Shafts and Cv Joint Service

28 Questions

Exam 125

Drive Axles and Differentials

22 Questions

Exam 126

Four-Wheel-Drive and All-Wheel Drive

24 Questions

Exam 127

Automatic Transmissiontransaxle Principles

22 Questions

Exam 128

Hydraulic Components and Control Systems

22 Questions

Exam 129

Automatic Transmissiontransaxle Diagnosis and In-Vehicle Service

19 Questions

Exam 130

Automatic Transmissiontransaxle Unit Repair

21 Questions

Show Answer